Davies Craig EWP115 Nylon Electric Water Pump & Controller Combo Kit

Description Take total control of your engine cooling with the Davies Craig EWP®115 Nylon Electric Water Pump and LCD EWP®/Fan Digital Controller. The Controller will also manage the operation of your Thermatic® Fan. Take total control of your engine cooling with the Davies Craig EWP®115 Nylon Electric Water Pump and LCD EWP®/Fan Digital Controller. The Controller will also manage the operation of your Thermatic® Fan. The EWP®115 (115 litres per minute) pump is suitable for small, medium, large, high-performance and 4WD vehicles. It improves engine cooling control and capacity whilst giving you more power and torque and improved fuel economy. Mechanical belt-driven water pumps run directly off the motor and sap engine power … the EWP®115 is hardwired into your electrical system, by-passing the engine and releasing up to an additional 10kw (13hp). Combined with the LCD EWP®/Fan Digital Controller, the pump continues to run after you’ve switched off, eliminating “heat soak” and extending engine life. Our EWP range are also extensively used in Intercooler Applications. This Kit Contains The Following Parts 1 x Nylon EWP115 Water Pump 1 x EWP/Fan Digital Controller & Mounting Plate Bracket 1 x Sensor Thermal – coolant temp – ¼” NPT thread 1 x Sensor Adaptor – Nylon – In Line, 38mm (2 x 1/4″ NPT) 1 x 1/4″ NPT Nylon – Bung 1 x Wiring Harness 1 x U-Bracket – For #8002 1 x Mounting Plate – For #8002 4 x Hose Clamps 1 x Blue 6mm Ring Terminal 1 x Screw – Self Tapping 8X3/8 BZ Davies, Craig’s revolutionary, Australian-designed EWP® pumps are made from anti-corrosive, lightweight nylon reinforced with fibreglass. Universal fit allows for easy mounting into the bottom radiator hose. Our kits come with easy-to-understand DIY instructions and everything you need for easy installation, including different adaptors to fit various hose sizes and all necessary electrical wiring. The EWP®115 and LCD EWP®/Fan Digital Controller Combo Pack is the most economical way to increase horsepower and save on fuel consumption whilst caring for your engine. The Davies, Craig EWP® header adaptor kit can replace the mechanical water pump completely. (See EWP Header Adaptors on website) TECHNICAL SPECIFICATIONS EWP150 – ELECTRIC WATER PUMP Operating voltage : 3V DC to 15V DC Maximum current : 10A @ 13V Flow rate (max) :115 L/min (30.38 US gal/min) @ 13V DC Operating temp. : -40° to 130°C (-40° to 266°F) Pump design : Clockwise centrifugal with volute chamber Pump weight : 920 grams (2.3 lb) Pump material : Nylon 66, 30% glass-filled Burst pressure: 500 kPa (72.5 psi) Seal : Ceramic face seal Self Priming : No, none of our pumps are self-priming Fits hose size : 35mm to 51mm (1.38” to 2”) Internal Fitting : -N/A No Internal Threaded Inlet or Outlet Push-On fitting Size : EWP Inlet & Outlet 38mm with 3mm Sleeve (#8510) 44mm with 6mm Sleeve (#8511) 51mm LCD FAN/PUMP CONTROLLER Voltage range : 12V DC to 29V DC Display LCD size : 64.6mm (2.54”) x 55.6mm (2.19”) Maximum current : 12Amps Warning alarm : High & low Temp., Above set temp., Sensor short circuit, Pump error, High & low voltage and Sensor open circuit Targeted (set) temperatures : Singular degrees from: 40°C (104°F)to 110°C (230°F) Memory : Set & targeted temperature Fan cut-in temp. : 3°C (5.4°F) above the targeted (set) temperature Controller type : PCB with micro-processor Sensor type : Thermister in housing Overrun/ shutdown : -10°C (14°F) below set/target temperature or 3 minutes Indicators : Temperature, power, EWP, test, fan, high & low temp, voltage, above set temperature (with alarm) Weight : 100 grams (3.5 oz) Dimensions : Length = 98mm (3.8″) Width = 95mm (3.7″) Depth = 25mm (1”)